- #ESTUDIO 4540C IMAGING KIT REPLACEMENT MANUAL#
- #ESTUDIO 4540C IMAGING KIT REPLACEMENT FULL#
- #ESTUDIO 4540C IMAGING KIT REPLACEMENT PC#
Įxpression of Colors and 4-Step Copy Process.
#ESTUDIO 4540C IMAGING KIT REPLACEMENT PC#
ĭisassembly and Replacement of Covers and PC boards. Symbols and Functions of Various Components. SPECIFICATIONS/ACCESSORIES/OPTIONS/SUPPLIES. Vorsicht : Entsorgung des gebrauchten Batterien und RAM-ICs (inklusive der Lithium-Batterie) nach diesem Handbuch.ġ.
Be careful not to reassemble small parts such as screws, washers, pins, E-rings, star washers in the wrong places.ħ.
#ESTUDIO 4540C IMAGING KIT REPLACEMENT MANUAL#
When parts are disassembled, reassembly is basically the reverse of disassembly unless otherwise noted in this manual or other related documents. Regarding the recovery and disposal of the equipment, supplies, consumable parts, packing materials, used batteries and RAM-ICs including lithium batteries, follow the relevant local regulations or rules.Ħ.Disposition of Consumable Parts, Packing Materials, Used batteries and RAM-ICs to see if there is any dirt on their surface and whether they are properly stuck to the equipment.ĥ. During servicing, be sure to check the rating plate and the cautionary labels such as “Unplug the power cord during service”, “Hot area”, “Laser warning label” etc.Do not use the parts not recommended by Toshiba TEC Corporation. If these parts are shorted circuit and/or made their functions out, they may burn down, for instance, and may result in fatal accidents. The breaker, door switch, fuse, thermostat, thermofuse, thermistor, etc.A fire may occur when dust lies on this area. Unplug the power cable and clean the area around the prongs of the plug once a year or more.Remove all watches, rings, bracelets, etc. that are reflective into the path of the laser beam. Avoid exposure to laser radiation during servicing.Use suitable measuring instruments and tools.When servicing the machines with the main switch turned on, be sure not to touch live sections and rotating/operating sections.Be careful when removing the covers since there might be the parts with very sharp edges underneath.Be sure not to touch rotating/operating sections such as gears, belts, pulleys, fan, etc.on them even after the power is turned OFF. Especially, the board of these components should not be touched since the electric charge may remain in the capacitors, etc. Be sure not to touch high-voltage sections such as the chargers, transfer belt, 2nd transfer roller, developer, IH control circuit, high-voltage transformer, exposure lamp control inverter, inverter for the LCD backlight and power supply unit.Be sure not to touch high-temperature sections such as the exposure lamp, the fuser unit, the damp heater and their periphery.Basically, be sure to turn the main switch off and unplug the power cord during service.The socket-outlet shall be installed near the equipment and shall be easily accessible.To insure adequate working space for the copying operation, keep a minimum clearance of 80 cm (32”) on the left, 80 cm (32”) on the right and 10 cm (4”) in the rear.Also provide proper ventilation as the equipment emits a slight amount of ozone.Select a suitable place for installation.Īvoid excessive heat, high humidity, dust, vibration and direct sunlight.Never ground it to a gas pipe or a water pipe. The equipment must be grounded for safety.Be sure to use a dedicated outlet with AC 110/13.2A, 115V or 127V/12A, 220V-240V or 240V/ 8A) for its power source.the control panel, ADU or RADF) when transporting the equipment. Be sure not to hold the movable parts or units (e.g.
#ESTUDIO 4540C IMAGING KIT REPLACEMENT FULL#
The equipment is quite heavy and weighs approximately 112kg (246 lb.), therefore pay full attention when handling it. When transporting/installing the equipment, employ four persons and be sure to use the positions as indicated below.The installation and service should be done by a qualified service technician. GENERAL PRECAUTIONS REGARDING THE INSTALLATION AND SERVICE FOR e-STUDIO3511/4511